Print this page
Click to view article in PDF format.
Click to view presentation (slides) in PDF format.
Laboratory and Field Observations of an Apparent Sub-Capillary-Equilibrium Water Saturation Distribution in a Tight Gas Sand 
Reservoir
*
K.E. Newsham1 and J.A. Rushing2
Search and Discovery Article #40400 (2009)
Posted May 4, 2009
*Adapted from paper prepared for presentation at the SPE Gas Technology Symposium held in Calgary, Alberta, Canada, 30 April–2 May 2002. Copyright held by the authors.
Authors’ Note: This paper was selected for presentation by an SPE Program Committee following review of information contained in an abstract submitted by the author(s). Contents of the paper, as presented, have not been reviewed by the Society of Petroleum Engineers and are subject to correction by the author(s). The material, as presented, does not necessarily reflect any position of the Society of Petroleum Engineers, its officers, or members.
1
SPE, Anadarko Petroleum Corporation; currently Apache Corporation, Houston, Texas ([email protected])
2
SPE, Anadarko Petroleum Corporation ([email protected])
This article documents laboratory and field observations of an apparent sub-capillary-equilibrium water saturation distribution in the Bossier tight gas sands. These observations are validated with consistent measurements from several different techniques, including production performance analysis, reservoir fluid phase behavior, log evaluation, and both conventional and special core analyses. We also identify several mechanisms, including those associated with a basin-centered gas system, which may be responsible for this phenomenon.
|
|
Tight gas sands constitute a significant percentage of the U.S. natural gas resource base and offer tremendous potential for future reserve growth and production. A recent study by the Gas Technology Institute (Prouty, 2001) indicated tight gas sands comprise almost 70% of gas production from all unconventional gas resources and account for 19% of the total gas production from both conventional and unconventional sources in the U.S. The same study (Prouty, (2001) estimated total producible tight gas sand resources exceed 600 tcf, while economically recoverable reserves are 185 tcf. This article focuses on one of the most active domestic U.S. tight gas sand plays, the Bossier Sands in the East Texas Basin. Specifically, we present results from a
Similar to conventional oil and gas systems, tight gas sands are often described by complex geological and petrophysical systems as well as heterogeneities at all scales. Unlike conventional reservoirs, however, tight gas sands often exhibit unique gas storage and producing characteristics. Consequently, effective exploitation of these resources requires accurate description of key
We present laboratory and field observations of the Bossier sands, a deep abnormally pressured, high-temperature tight gas sand Regional Geology and Depositional Environment The Bossier sands are Late Jurassic in age and were deposited in the East Texas Basin. Located in northeast Texas, this sedimentary basin is a deep elongated trough structure with shelf-slope systems on the basin flanks. Several major tectonic features, including the Sabine Uplift to the east, the Mexia-Talco Fault System to the north and west, and the Angelina-Caldwell Flexure to the south bound the basin (Montgomery, 2000). East Texas is recognized as one of three major salt provinces in the U.S. The East Texas Basin is characterized by major salt features - salt anticlines, piercement domes, pillows, etc. within its interior (Montgomery, 2000). Current geological models suggest a relationship between generation of the major fault systems, salt deformation and migration, basin subsidence, and sediment deposition during Middle to Late Mesozoic (Montgomery, 2000). The significant salt structures also appear to control the distribution of sediments within the basin interior (Montgomery, 2000). A typical stratigraphic column for the East Texas Basin (Figure 1) shows that the Bossier sands are part of the Upper Jurassic Cotton Valley Group and are overlain by the Cotton Valley Sandstone (Montgomery, 2000). The Bossier interval is thick and lithologically complex and contains black to gray-black shale interbedded with very fine- to fine-grained argillaceous sandstone. Similarly, the Cotton Valley Sandstones are comprised of interbedded shale and very quartz rich sandstone layers. The Cotton Valley Group is underlain regionally by the Upper Jurassic Louark Group. This includes other hydrocarbon-bearing formations such as the Smackover carbonates and Haynesville/Cotton Valley Limestones. Overlying the Cotton Valley Group is the regionally productive, Lower Cretaceous Travis Peak and Pettit (Sligo) formations. As illustrated by the generalized regional dip-section in Figure 2, Bossier deposition represents cycles of sand progradation into the basin onto organic rich mud, succeeded by marine transgression. Much of the Bossier interval downdip appears to be time equivalent to the Cotton Valley Sandstone updip and represents prodelta/delta front material related to Cotton Valley deltaic systems (Montgomery, 2000; Perrizela, 2002). The Bossier sands appear to originate from the north and west and were transported downslope by slumping, debris flow, and turbidity currents. Significant Bossier sand thicknesses are located in topographic lows created by a combination of faulting, subsidence, and salt movement in the basin. Bossier Sand Characteristics of the Mimms Creek and Dew Fields
The current Bossier sand play is centered along the western shelf margin of the East Texas Basin, specifically in Robertson, Leon, Limestone, and Freestone counties. In this section we summarize the Sand Facies and Depositional Environment The Bossier sands in Mimms Creek and Dew fields are comprised of a series of stacked sandy packages, as illustrated by the type log in Figure 3. In chronological order of deposition, these packages are known as the York, Bonner, Shelley, and Moore sands. Stratigraphic sequences observed from several whole cores indicate the sands were deposited as a prograding sediment wedge complex during a lowstand onto organic shelf mud deposited during a highstand. At the top of the sand packages, ravinement or transgressive lag deposits have been observed, indicating the onset of a marine transgression during which very little sand was preserved above wave base. The Bossier sands are capped by restricted to open shelfal muds deposited during another highstand (Perrizela, 2002). As illustrated in Figure 4, typical Bossier sand-body geometry is elongated with the long axis oriented parallel to the depositional dip; so lateral continuity along depositional strike is often limited. The sand-body thickness varies from tens to several hundred feet. The combination of low depositional relief and limited lateral sand continuity minimizes the hydrocarbon column height potential within each sand body. In addition, the elongated geometry of the isolated sand bodies combined with low permeability and high degree of heterogeneity limits the volume of recoverable gas from a single well. This observation is confirmed from production decline type curve analysis which indicates small drainage areas, typically ranging from 40 to 80 acres but frequently less than 40 acres per well.
The Bossier shales are prevalent both areally and vertically in Mimms Creek and Dew fields. Laterally extensive shales appear to act as both seals and hydrocarbon source rock for the sands, while local interbedded shales also appear to be an important hydrocarbon source for the Bossier sands. A As we discuss in the next section, most of the Bossier section in the Mimms Creek and Dew fields is abnormally overpressured. A probable source for this overpressured system is gas generation from the shales. The data suggests hydrocarbons have been generated not only from kerogen cracking in the shales but also from cracking of liquid hydrocarbons trapped in the sands. This cracking phenomenon, which has been documented by Hunt (1990), has been postulated on the basis of pyrobitumen observed in core thin sections. We also conducted gas isotope analysis on Bossier gas samples, and the computed carbon isotope separations (δ13C) range from –30 ppt to –40 ppt which is consistent with gases of thermal origin. Gases produced from the Mimms Creek and Dew fields are composed primarily of methane, but we also measure ethane and small quantities of propane, which are also indicative of thermal rather than biogenic origin. Pressure and Temperature Gradients The Bossier Sands are overpressured throughout most of the East Texas Basin, including the Mimms Creek and Dew Field area. As illustrated by Figure 3, pressure gradients range from 0.50 to 0.55 psi/ft in the upper Cotton Valley Sands, 0.60 to 0.65 psi/ft in the upper Bossier, Moore, and Shelley Sands, and 0.70 to 0.90 psi/ft in the lower Bossier Bonner and York Sands. The Cotton Valley Sand pressure gradient represents a normal to slightly abnormal pressure gradient of a very saline formation water column (>220,000 ppm NaCl). A pressure transition exists throughout the Bossier interval with the pressure gradient increasing with depth in a basinward direction. This overpressured system, which has been confirmed using both static bottomhole pressure measurements and from acoustic log analysis (Figure 5), is easily recognized by pressure-depth profiles. The deviation from the normal pressure gradient is referred to as the top of abnormal pressure (TAG) point. The overpressure gradient, when calculated from mean sea level, increases with depth; however, the pressure transition trend, referred to as the incremental pressure gradient (IPG), ranges from 3.5 psi/ft to 5.00 psi/ft. Note that the IPG is significantly greater than the lithostatic gradient. The inequality between the lithostatic and incremental pressure gradients suggests the source of overpressure is not caused by compaction/disequilibrium (Swarbrick and Osborne, 1998; Finkbeiner, 2001). Rather, we believe the source of overpressure is primarily from hydrocarbon generation and secondarily from chemical compaction effects of diagenesis. Bossier sands in this area and throughout the East Texas Basin also exhibit abnormally high temperature gradients. Bottomhole temperatures in the Mimms Creek and Dew fields range from 280oF to 325oF at depths ranging from 12,500 ft to 13,500 ft. This corresponds to temperature gradients of 2.2 to 2.4oF per 100 ft of depth. Typical Producing Characteristics
The average initial gas production rates vary from 2 to 5 MMscfd in the Moore and Shelley sands, while the Bonner and York sands range from 5 to 15 MMscfd. Similarly, the estimated ultimate gas recovery ranges from 1.5 to 3 Bcf in the Moore and Shelley sands and 3 to 10 Bcf in the Bonner and York. Most wells exhibit hyperbolic decline with stabilized rates of 500 to 900 Mscfd after two to three years. The differences between producing characteristics in the sands reflect both better
The Bossier sands also produce some water. Initial water production rates, which range from 50 to 100 bbl/d for the first one to three months, can be attributed to clean-up of stimulation fluids. However, most wells produce between 1 to 5 bbl/day for the life of the well. Because of the low permeability of the Bossier sands, we do not believe a mobile liquid phase exists in the Wells completed in the Bossier sands produce a dry to slightly wet gas, with specific gravity ranging from 0.58 to 0.61. Condensate production averages one to three STB/MMscf over the life of the well. Gas composition typically averages 94 mole% methane and 2 mole% ethane. The remaining hydrocarbon mixture includes fractional percentages of propane through hexane, with typically no heptanes plus. Non-hydrocarbon components include 2 to 2.5 mole% carbon dioxide, 0.2 to 0.5 mole% nitrogen, and relatively no hydrogen sulfide.
As we noted above, the Bossier sands produce some water; however, we believe that no mobile liquid water phase exists in the
Intrinsic Rock We have also conducted a comprehensive Bossier sand description program, using evaluations of more than 1000 ft of whole core obtained from four wells in the Mimms Creek and Dew fields. Our description includes classification of petrophysical rock types, which are identified based on similar pore and grain scale characteristics, such as composition, texture, mineralogy, clay type, and types of diagenesis. We have also defined several hydraulic rock types representing similar ranges of storage and flow characteristics. Table 1 summarizes the various measurements made to describe the Bossier sands. The petrographic rock types observed within the Bossier Sands (Newsham and Rushing, 2001) include clean sandstone, argillaceous/weakly laminated sandstone, dolomitic sandstone, and argillaceous/burrowed siltstone (Newsham and Rushing, 2001). Using the Folk (1974) classification, the types range from subarkose to sublitharentite to lithic wackes. The framework grains contain, on average, 84% quartz, 6.5% feldspar, and 9.5% rock fragments. The range for these constituents is 41%-94% for quartz, 0%-11.7% for feldspar, and 0.5%-59% for the rock fragments. The intergranular constituents are primarily quartz overgrowths, diagenetic clay in the sands, detrital clay found in sand and silt, dolomite cement, and local pyrite. The clay fraction is dominantly grain-coating chlorite and illite. Texturally, the Bossier Sands have a narrow range of grain size, typically from upper very fine to fine. The sands are medium to well sorted, while the silts are typically poorly sorted. Sand grain shape is subangular to well rounded. A significant degree of compaction is observed from thin sections in the form of suturing, elongation of grain contacts, and ductile grain deformation.
Bossier sands also exhibit a significant diagenetic overprint. Diagenesis, the physical or chemical processes that cause changes in the initial rock
We have also identified several Bossier sand hydraulic rock types (Newsham and Rushing, 2001). When described on the basis of the dominant pore throat diameter determined from high-pressure mercury capillary pressure data, we observed distinct groupings of rocks having similar flow and storage Effective Porosity and Absolute Permeability
Figure 7 shows a typical distribution of effective porosity and absolute permeability. Effective porosity varies from 1% to 17%, while absolute permeability ranges from 0.001 to 1 mD. Non- Similar to most tight gas sands, the Bossier sands display both stress-dependent porosity and permeability characteristics. For example, the hyperbolic decline behavior exhibited by many tight gas sand wells can be attributed, in part, to reductions in permeability and porosity during the depletion history. We measured porosity and permeability over a wide range of stress conditions and observed slight changes in porosity. We did, however, measure significant reductions in permeability as net mean stress is increased. We also noticed that the degree of stress dependency increased for the lower quality rock types. Effective and Relative Permeability
Although we believe no mobile liquid phase exists in the Bossier sands at
We also measured connate water saturation from more than 500 Bossier whole core plugs. Since the whole core was obtained with a low invasion, oil-base mud system, we were able to obtain consistent and accurate estimates of in-situ connate water saturation. We used the Dean Stark solvent extraction technique with toluene as the solvent. Most of the non- Capillary Pressure Characteristics We measured capillary pressure characteristics using high-pressure, mercury injection (MICP). We used MICP since the low porosity and permeability precluded using either centrifuge or porous plate methods, which are limited by the maximum attainable pressure. From the capillary pressure measurements, we were able to describe the vertical water saturation distribution (Leverett, 1041; Gunter, 1999; Negabahn et al., 2000), range of irreducible water saturation, and capillary seal capacity. As noted above, we also identified hydraulic rock types using capillary pressure characteristics.
To verify the low water saturations measured from the core plugs, we initiated a rigorous evaluation and validation program composed of three methods:
Core-Based Water Saturation Measurements
We obtained more than 1000 ft of whole core from four wells in the Mimms Creek and Dew fields. To minimize invasion effects and preserve connate water saturation, we used an oil-base mud system.
Water saturation was measured directly with the Dean Stark solvent extraction process using toluene as the solvent. On the basis of more than 500 plugs, we observed water saturations ranging from as low as 5% in the best Log-Based Water Saturation Calculations We also computed the vertical distribution of water saturation in the same wells from which the core was obtained. The best match between core-based and log-based water saturation was obtained with the Modified Simandoux (1963) shaly sand model. Shale volume was estimated from the gamma ray response and porosity cross-plot techniques, while effective porosity was computed from a neutron-density cross-plot corrected for shale and gas effects.
Application of the Modified Simandoux (1963) model also requires estimates of the Archie (1950) saturation exponent, n, and the cementation exponent, m. These parameters were measured in the laboratory using both two-and four-electrode resistivity devices. Core samples were saturated with a 220,000 ppm brine, and all measurements were made at initial
The final component required to compute connate water saturation is water resistivity, Rw, at
Commutation or residual salt analysis is a process that extracts or leaches connate water and the associated salts from preserved core samples using ultra-pure, deionized water. Salt concentration and composition in the leachate are measured using an atomic absorption or mass spectrometer technique, while salinity is estimated from material balance calculations. Salinity measurements in the Bossier sands ranged from 200,000 to 230,000 ppm.
In general, results from the log-based analysis agreed with water saturation estimates from the core measurements in the Capillary-Equilibrium-Based Water Saturation Calculations
As we noted above, we also attempted to compute a vertical distribution of water saturation from capillary pressure characteristics to verify the apparent unusually low water saturations from the core and logs. We converted capillary pressures to height above free water and plotted them against water saturation. Our current understanding of the Bossier Sand geology in the Mimms Creek and Dew fields indicates the sands were deposited on a low-relief shelf/slope topography and appear to be laterally discontinuous. Under these conditions, the total relief is about 200 ft. Using this total column height, the computed range of irreducible water saturation is 35% to 100% for the Because of these discrepancies, our next step was to determine the column height required to match the range of water saturations determined from core and log analyses. Our calculations indicate an average total column height of 1000 ft is required to generate irreducible water saturations from 5% to 50% for rock types 1 through 3A, respectively. As shown by a solid horizontal line in Figure 11, this is consistent with the average seal capacity of the sealing facies. The capillary seal facies have a seal capacity ranging from 700 ft to 2000 ft and an average capacity of 1000 ft at a displacement saturation of 7.5%. This average seal capacity represents the upper threshold of column height for sands having 1000 ft of total relief. Current depositional and geological models of the Mimms Creek and Dew fields do not, however, support a 1000-ft column height. Sub-capillary-Equilibrium Water Saturation Concept
In summary, vertical distributions of core-derived measurements and log-derived calculations of water saturation cannot be matched with estimates from capillary pressure characteristics unless we make unrealistic assumptions about sand geology and structure, particularly column height. This observation suggests the vertical distribution of water saturation in the Bossier sands may not be in capillary equilibrium. In fact, measured water saturation is much lower than that which would be predicted by capillarity; i.e., a sub-capillary-equilibrium or sub-irreducible water saturation condition. We also observed an abnormally high capillary pressure profile associated with the low water saturations. Although not common in the Possible Mechanisms for Sub-Capillary-EquilibriumWater Saturation Phenomenon
In this section, we present a hypothesis to explain the physical mechanisms and conditions that could cause the development of a sub-capillary-equilibrium, water saturation distribution. We also present a geological process model under which this phenomenon would most likely occur. Our model is discussed as part of a total
Elements of our
During all stages of shale diagenesis, hydrocarbons are frequently expelled from the shales and migrate into
The critical element in our model is a mechanism to remove connate water effectively and transport the water up the vertical section. It has been recognized that several mechanisms can remove connate water from
Consequently, we have identified another mechanism for removing connate water. We believe the key element required to remove water effectively is the process of vaporizing connate water into the gas phase. Laboratory data suggests that, at temperatures exceeding 280oF to 300oF, significant volumes of water vapor may be dissolved in the hydrocarbon gas (McCain, 1990). Furthermore, the solubility of water vapor in gas is enhanced when non-hydrocarbon gases, such as CO2 and H2S, are present. We believe that most of the connate water displaced from the Bossier sands is in the form of water vapor dissolved in the hydrocarbon gas. Gas generated and expelled from the shales is dry (i.e., initially no dissolved water vapor). As long as hydrocarbon gases continue to migrate into the
The final element required to explain a sub-capillary-equilibrium water saturation distribution is related to the hydrocarbon generation potential of the shales. For very organic-rich shales, hydrocarbon generation and migration may continue for thousands of years. Furthermore, if hydrocarbon migration into the We have documented an apparent sub-capillary-equilibrium water saturation distribution in the Bossier sands in the Mimms Creek and Dew fields, Freestone County, Texas. Our observations are based on consistent measurements and calculations from several different techniques and data sources. We have also postulated that the Mimms Creek and Dew fields may be part of a basin-centered gas system, and the mechanisms responsible for that system may have contributed to the unusually low water saturation distribution. We also believe that the Bossier sands in the Mimms Creek and Dew fields are not in capillary equilibrium. Finally, we have identified and provided evidence that water vaporization and dissolution in the hydrocarbon gas may be an effective mechanism for removing and transporting connate water up the vertical column.
We would like to express our thanks to Anadarko
Archie, G.E., 1950, Introduction to petrophysics of Espitalie, J., Deroo, G., and Marquis, F., 1985, La pyrolyse Rock-Eval et ses applications: Rev. Inst. Fr. Pet. 40, p. 563579, p. 755-784, Rev. Inst. Fr. Pet. 41, p. 73-89. Finkbeiner, T., Zoback, M., Flemmings,. P., and Stump, B., 2001, Stress, pore pressure, and dynamically constrained hydrocarbon columns in the South Eugene Island 330, northern Gulf of Mexico: AAPG Bulletin, v.85, no.6 (June 2001), p. 1007-1031. Folk, R.L., 1974, Petrology of Sedimentary Rocks: Hemphill Publishing Co., Austin, Texas, 78703.
Gunter, G.W., et al., 1997, Early determination of
Hunt, J.M., 1990, Generation and migration of Law, B. E., 1984a, Relationships of source rocks, thermal maturity, and overpressuring to gas generation and occurrence in low-permeability Upper Cretaceous and lower Tertiary rocks, Greater Green River Basin, Wyoming, Colorado, and Utah, in Woodward, J., Meissner, F.F., and Clayton, J.L., eds., Hydrocarbon source rocks of the greater Rocky Mountain region: Rocky Mountain Association of Geologists, p. 469-490. Law, B.E., 1984b, ed., Geological characteristics of low-permeability Upper Cretaceous and Lower Tertiary rocks in the Pinedale anticline area, Sublette County, Wyoming: U.S. Geological Survey Open-File Report 84-753, 107 p. Law, B.E., 1995, Columbia Basin-basin-centered gas play (0503), in Tennyson, M.E., Eastern Oregon-Washington Province (005), in Gautier, D.L., Dolton, G.L., Masters, J.A., 1979, Deep basin gas trap, western Canada: AAPG Bulletin, v. 63, p.152-181. Law, B.E., and Dickinson, W.W., 1985, A conceptual model for the origin of abnormally pressured gas accumulations in low-permeability reservoirs: AAPG Bulletin, v.69, p.1295-1304. Leverett, M.C., 1941, Capillary behavior in porous sands, Trans. AIME, 1941. Gunter, G., et. al., 1999, Saturation modeling at the well log scale using petrophysical rock types and a classic non-resistivity based method: 40th Annual SPWL Symposium, Paper ZZ. Masters, J.A., 1984, ed., Elmworth - Case study of a deep basin gas field: AAPG Memoir 38, 316 p. Matinsen, R.S, 1994, Summary of published literature on anomalous pressures: implications for the study of pressure compartments, in Ortoleva, P.J. ed., AAPG Memoir 61, 1994.
McCain, W.D., 1990, The Meissner, F.F, 1987, Mechanisms and patterns of gas generation/storage/explusion-migration/accumulation associated with coals measures in the Green River and San Juan Basins, Rocky Mountain. Region, USA, in Dolgigez, B., ed.,Migration of hydrocarbons in sedimentary basins:, 2nd IFP Exploration Research Conference, Carcias, France, June 15-19, 1987, Editions Technip. Paris, p. 79-112.
Montgomery, S., 2000, East Texas Basin Bossier gas play in Negabahn, S., et.al., 2000, An improved empirical approach for prediction of formation water saturation and free water level for uni-modal pore systems: SPE 63282, 2000 SPE Annual Technical Conference and Exhibit, Dallas, TX., October 1-4, 2000. Newsham, K.E., and Rushing J.A., 2001, An integrated work-flow model to characterize unconventional gas resources—Part I: Geological assessment and petrophysical evaluation: Paper SPE 71351 presented at the 2001 SPE Annual Technical Conference and Exhibition, New Orleans, LA, Oct. 1-3. Nuccio, V.F., Schmoker, J.W., and Fouch, T.D., 1992, Thermal maturity, porosity, and lithofacies relationships applied to gas generation and production in Cretaceous and Tertiary low-permeability (tight) sandstones, Uinta Basin, Utah., in Fouch, T.D., Nuccio, V.F., and Chidsey, T.C., Jr., eds., Hydrocarbon and mineral resources of the Uinta Basin, Utah and Colorado: Utah Geological Association Guidebook 20, p. 77-94. Perrizela,P. , 2002, OMNI Core description reports, McAdams A7, Henderson 6, and Burgher D7. Pittman, E.D., 1992, Relationship of porosity and permeability to various parameters derived from mercury injection-capillary pressure curves for sandstone: AAPG, v. 76, no. 2 (February 1992), p. 191-198. Prouty, J.L., 2001, Tight gas in the spotlight,” in GasTIPS, Gavin, J.J. and Lang, K.R., eds., Gas Technology Institute, v. 7, no. 2, Chicago, IL (2001), p.. 4-10. Ryder, R.T., SanFilipo, J.R., Hettinger, R.D., Keighin, C.W., Law, B.E., Nuccio, V.F., Perry, W.J., and Wandrey, C.J., 1996, Continuous-type (basin-centered) gas accumulation in the Lower Silurian "Clinton" sands, Medina Group, and Tuscarora Sandstone in the Appalachian Basin: AAPG Bulletin, v. 80, p. 1531. Simandoux, P.,1963, Measures dielectrique en milieux poreux, application a measure de saturation en eau, etude des massifs argileaux: Revue de l’institut Francais du Petrole, Supplement issue, 1963, p. 193-215. Spencer, C.W., 1987, Hydrocarbon generation as a mechanism for overpressuring in the Rocky Mountain region, AAPG Bulletin v. 71, no. 4 (April 1987), p. 368-388. Swanson, B.F., 1979, A simple correlation between permeabilities and mercury capillary pressure: Paper SPE 8234, 54th Annual Technical Conference and Exhibition, Las Vegas, NV, September 23-26, 1979. Swarbrick, R.E., and Osborne, M.J., 1998, Mechanisms that generate abnormal pressures: an overview, in Law, B.E., Uimishek, G.F., and Slavin, V.I., eds., Abnormal pressures in hydrocarbon environments: AAPG Memoir 70, p. 13-34. Takahashi, K.1., and Varnes, K., eds., 1995 National assessment in the United States of oil and gas resources: Results, methodology, and supporting data: U.S. Geological Survey Data Series 30. Thompson, A.H., et al., 1987, Estimation of absolute permeability from capillary pressure measurements: Paper SPE 16794 presented at the 1987 SPE Annual Technical Conference and Exhibition, Dallas, Texas, September 27-30. Washburn, E.W., 1921, Note on a method of determining the distribution of pore sizes in a porous material: Proceedings of the National Academy of Science, v. 7, p.115-116.
2002©K.E. Newsham and J.A. Rushing
|
